16-bit serial-in parallel-out shift register module using 74HC595. Module contains two 74HC595 ICs. Each IC will have eight outputs. From two ICs, there will be 16 outputs.
Interfacing 16-bit serial-in parallel-out shift register module to Arduino UNO : https://haberocean.com/2020/01/interfacing-16-bit-serial-in-parallel-out-shift-register-module-to-arduino-uno/
Cascading two 16-bit serial-in parallel-out shift register modules using Arduino UNO : https://haberocean.com/2020/01/cascading-two-16-bit-serial-in-parallel-out-shift-register-modules-using-arduino-uno/
32-bit serial-in parallel-out shift register module using 74HC595. Module contains four 74HC595 ICs. Each IC will have eight outputs. From four ICs, there will be 32 outputs.
Interfacing 32-bit Shift register module to Arduino UNO : https://haberocean.com/2020/08/32-bit-shift-register-module-using-74hc595-controlled-using-arduino-uno/
Cascading two 32-bit shift register modules using Arduino UNO : https://haberocean.com/2020/08/cascading-two-32-bit-shift-register-modules-using-arduino-uno/
Purchase from Flipkart : https://www.flipkart.com/haberocean-2-double-sided-pcb/p/itmac4c5ff65d627?pid=LBOG5AFHHCGZPTGW
Connector module (Yellow module only) between 32-bit serial-in parallel-out shift register module and 7-digit seven segment display module
Connector module between 32-bit serial-in parallel-out shift register module and 7-digit seven segment display module which will simplifies the connection between these two modules so that we could easily display our desired value on the 7-digit seven segment display from Arduino or ESP-12F IOT module.
Purchase from Amazon : http://www.amazon.in/dp/B07TYKMFV3?ref=myi_title_dp
DS3231 is a six terminal device, out of them two pins are not compulsory to use. So we have mainly four pins. These four pins are given out on other side of module sharing the same name (Battery will not be included).
DS3231 RTC MODULE Features
- RTC counts seconds, minutes, hours and year
- Accuracy: +2ppm to -2ppm for 0ºC to +40ºC , +3.5ppm to -3.5ppm for -40ºC to +85ºC
- Digital temperature sensor with ±3ºC accuracy
- Two Time-of-day alarms
- Programmable square wave output
- Register for Ageing trim
- 400Khz I2C interface
- Low power consumption
- Automatic power failure battery switch circuitry
- CR2032 battery backup with two to three year life
- Potable size
DS3231 RTC MODULE Specifications
- Operating voltage of DS3231 MODULE: 2.3V – 5.5V
- Can operate on LOW voltages
- Consumes 500nA on battery backup
- Maximum voltage at SDA , SCL : VCC + 0.3V
- Operating temperature: -45ºC to +80ºC
ESP32-S2-WROVER is a powerful, generic Wi-Fi MCU module that integrates ESP32-S2. It has a PCB antenna, a 4 MB external SPI flash and an additional 2 MB PSRAM.
All available GPIO pins (except for the SPI bus for flash and PSRAM) are broken out to the pin headers on the board. Users can program ESP32-S2 chip to enable multiple functions such as SPI, I2S, UART, I2C, touch sensors, PWM etc.
A four digit UP counter module designed using CD4026 ICs which can be used to count from 0 to 9999. Count will increment in each LOW to HIGH pulses applied at the CLK input of counter module. Module can be used to count motion easily by connecting a PIR motion sensor directly to the module. No programming required.
0 -9999 counter without RESET option from Arduino, Circuit and program : https://haberocean.com/2020/03/0-9999-counter-module-using-arduino-uno/
0 -9999 counter with RESET option from Arduino, Circuit and program : https://haberocean.com/2020/03/0-9999-up-counter-with-reset-from-arduino-uno/
Motion counter using PIR motion sensor and 4 digit UP counter module : https://haberocean.com/2020/08/motion-counter-using-pir-motion-sensor-and-4-digit-up-counter-module-using-cd4026/